Remeha W23c
Verwarmingsketel · 25 Probleemoplossingen
Probleemoplossing - Remeha W23c
Veelvoorkomende problemen en oplossingen - ook zonder foutcode op het display.
Prestaties & Werking 11
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Waakvlam dooft | De waakvlam is te klein | Meer gas toevoeren d.m.v. de waakvlaminstelschroef ('pilot'). Waakvlamgasverbruik afstellen op ca. 19 l/uur (0,019 m3/uur). |
| Waakvlam blaast af | Te veel gas wordt toegevoerd | Minder gas toevoeren d.m.v. de waakvlaminstelschroef ('pilot'). |
| Thermokoppelspanning is te laag | Het thermokoppel is defect of verkeerd gemonteerd ten opzichte van de waakvlambrander, of de weerstand in het thermokoppelcircuit is te hoog | Controleer de aansluitingen in het circuit van de maximaalthermostaat en het thermokoppel. Bij vervanging van het thermokoppel uitsluitend een origineel Remeha thermokoppel art.nr. S49.800 toepassen. |
| Gasdruk is weggevallen | Geen gasdruk beschikbaar | Na herstel van de gasdruk de waakvlam opnieuw ontsteken (netvoeding ingeschakeld laten). |
| Circulatiepomp is defect | Circulatiepomp functioneert niet goed | Controleer de circulatiepomp. |
| Temperatuursensor of pompthermostaat is defect | Sensor of thermostaat functioneert niet goed | Controleer de temperatuursensor c.q. pomphermostaat. Deze dienen met behulp van gereedschap te worden gedemonteerd en gemonteerd, NIET draaien aan de fastonnen (aansluitlipjes). |
| Ventilator draait niet | Ventilator is geblokkeerd door bouwvuil of ventilator is defect | Controleer de ventilator op blokkades door bouwvuil en verwijder deze eventueel. Controleer of de ventilator defect is. |
| Exhaust gas fan does not rotate | Fan is not functioning | Check the exhaust gas fan. |
| Air pressure differential switch does not switch to safe position | Air supply or combustion gas discharge path is blocked | Check the air supply and combustion gas discharge path for blockages. The air pressure differential switch activates at a pressure difference of at least 0.7 mbar. |
| Comfort valve remains in closed position | Comfort valve is not functioning properly or is stuck due to condensation in the exhaust gas discharge line | Check the operation of the comfort valve. A stuck comfort valve may indicate condensation in the exhaust gas discharge line. |
| Boiler starts operating but shuts down immediately afterwards | Exhaust gas system does not discharge the exhaust gases or discharges them insufficiently | Check the air supply and exhaust gas system as well as the comfort valve and heat exchanger for dirt. Check the comfort valve for proper operation. |
Stroomvoorziening & Elektronica 2
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Voedingsspanning is weggevallen | Stroomtoevoer onderbroken | Zorg voor herstel van de voedingsspanning. De waakvlam is gedoofd doordat de ventilator is gestopt en de verbrandingsgassen niet worden afgevoerd. |
| Fuse defective | Fuse has blown | After switching off the power supply, replace the defective fuse(s). |
Temperatuurproblemen 7
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Maximaalthermostaat spreekt aan | De maximaalthermostaat is defect, de pompthermostaat is defect zodat de pomp niet wordt gestart, of het filter in de warmtewisselaar zit dicht | Controleer of de maximaalthermostaat defect is, controleer of de pompthermostaat defect is, of reinig het filter in de warmtewisselaar (zie Par. 12.3). |
| Heating system does not reach temperature | The filter in the heat exchanger is clogged, causing the boiler block temperature to rise and the boiler to modulate prematurely | Clean the filter in the heat exchanger (see fig. 04, pos. 23 or fig. 05, pos. 26) according to Section 12.3. |
| Lange wachttijden sanitair warmwater - keteltemperatuur te laag ingesteld | Keteltemperatuur is op een lagere waarde dan 70°C ingesteld | Stel de keteltemperatuur hoger in. Dit is alleen van invloed tijdens of direct na cv-warmtevraag. In rusttoestand wordt de warmtewisselaar op 70°C gehouden onafhankelijk van de instelling van de regelthermostaat. |
| Lange wachttijden sanitair warmwater - vloerverwarmingsysteem onttrekt warmte | Vloerverwarmingsysteem is ingeschakeld waarvan de pomp warmte onttrekt uit warmtewisselaar | Zie Par. 7.8.3 voor richtlijnen. |
| Lange wachttijden sanitair warmwater - thermosyphon werking | Thermosyphon werking veroorzaakt warmteverlies | Plaats een terugslagklep (zie Par. 7.8.6). |
| Tapwater komt niet op temperatuur | Het filter in de warmtewisselaar zit dicht waardoor ketelbloktemperatuur stijgt en ketel voortijdig gaat moduleren | Reinig het filter in de warmtewisselaar (zie afb. 04, pos. 23 of afb. 05, pos. 26) volgens Par. 12.3. |
| Lange wachttijden op tapwater door grote leidinglengte of leidingdiameter | Leidinglengte en/of leidingdiameter naar het verstgelegen tappunt zijn te groot | Draai de warmwaterkraan aanvankelijk niet geheel open maar b.v. op een hoeveelheid van ca. 3 l./min., zodat de opwarmtijd bekort wordt. |
Waterproblemen 5
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Toestel is onvoldoende met water gevuld | Waterdruk is te laag | Controleer de waterdruk en vul zonodig de installatie bij. |
| Boiler supplies insufficient or no hot water - flow limiter contaminated | Flow limiter is contaminated | Check the flow limiter. |
| Boiler supplies insufficient or no hot water - three-way valve is not functioning | Three-way valve is contaminated or central shaft moves with difficulty | Check the three-way valve for contamination and smooth operation of the central shaft (lubricate if necessary). |
| Boiler supplies insufficient or no hot water - cold water supply tap not fully opened | Cold water supply tap is not fully open | Turn the cold water supply tap fully open. |
| Boiler supplies insufficient or no hot water - low water mains pressure | Water mains pressure is low | If necessary, remove the flow limiter (see Section 7.10). |
Community-vragen
Stel een vraag
De foutcodes zijn afkomstig uit de officiële handleiding van de fabrikant.