ATAG Energion Nuos Plus 200
Ketel & boiler · 27 Display-foutcodes · 33 Probleemoplossingen
Foutcodes - ATAG Energion Nuos Plus 200
Deze codes worden op het display van uw apparaat weergegeven wanneer er een probleem wordt gedetecteerd.
Meest voorkomende foutcodes - ATAG Energion Nuos Plus 200
021
Gas Leak
KRITIEK
032
Compressor Issue
KRITIEK
053
Compressor Thermal Protector: KO
KRITIEK
232
Water Temperature sensor (Heating Element Zone): safety inte...
KRITIEK
233
Relay blocked
KRITIEK
| Foutcode | Beschrijving | Oplossing | Ernst |
|---|---|---|---|
| 021 KRITIEK | Gas Leak | Verify compressor inlet sensor proper functioning. If error persists, recover residual gas; find leak in cooling circuit; repair it; make vacuum and recharge circuit with 1100g of refrigerant gas | KRITIEK |
| 032 KRITIEK | Compressor Issue | Check power voltage on compressor connector. Turn off the appliance | KRITIEK |
| 053 KRITIEK | Compressor Thermal Protector: KO | Check compressor connector | KRITIEK |
| 232 KRITIEK | Water Temperature sensor (Heating Element Zone): safety intervention (2nd level) | Verify sensor proper functioning | KRITIEK |
| 233 KRITIEK | Relay blocked | Reset the appliance by pressing the ON/OFF button twice. If the error persists, replace the motherboard | KRITIEK |
| 321 KRITIEK | Corrupted data | Reset the product by pressing the ON / OFF button twice. If the error persists, replace the motherboard | KRITIEK |
| 331 KRITIEK | Missing communication between Main Board and HMI | Reset the product by pushing the ON/OFF button twice. If the error persists, replace the mainboard-display communication wiring | KRITIEK |
| 335 KRITIEK | Safety board communication failure | Reset the product by pressing the ON / OFF button twice. If the error persists, replace the motherboard | KRITIEK |
| 007 WAARSCHUWING | NTC Condenser: Open or Short Circuit | Verify NTC Condenser proper functioning | WAARSCHUWING |
| 008 WAARSCHUWING | NTC Discharge (Compressor Outlet): Open or Short Circuit | Verify NTC Discharge proper functioning | WAARSCHUWING |
| 009 WAARSCHUWING | NTC Air: Open or Short Circuit | Verify NTC Air proper functioning | WAARSCHUWING |
| 010 WAARSCHUWING | NTC Evap: Open or Short Circuit | Verify NTC Evap proper functioning | WAARSCHUWING |
| 012 WAARSCHUWING | NTC Suction (Compressor Inlet): Open or Short Circuit | Verify NTC Suction proper functioning | WAARSCHUWING |
| 042 WAARSCHUWING | Evaporator Obstructed | Check that the evaporator and the external unit casing is not obstructed | WAARSCHUWING |
| 044 WAARSCHUWING | Fan Issue | Check power voltage on fan connector. Control the proper functioning of sensor at compressor inlet | WAARSCHUWING |
| 051 WAARSCHUWING | High Pressure | Check pressure switch wiring. Verify gas quantity | WAARSCHUWING |
| 081 WAARSCHUWING | Electronic Expansion Valve Issue | Verify expansion valve cables. Verify NTC suction and NTC Evap correct functioning | WAARSCHUWING |
| 218 WAARSCHUWING | Dome NTC sensor (hot water): Open or Short Circuit | Verify NTC sensor (hot water) proper functioning | WAARSCHUWING |
| 230 WAARSCHUWING | Water Temperature Sensor (Heating Element Zone): Open or Short Circuit | Check the correct assembly of sensor wiring on related mainboard connector. Verify sensor proper functioning | WAARSCHUWING |
| 231 WAARSCHUWING | Water Temperature sensor (Heating Element Zone): safety intervention (1st level) | Verify sensor proper functioning | WAARSCHUWING |
| 241 WAARSCHUWING | Impressed Current Anode: Open Circuit | Check the presence of water inside the product. If the error persists, verify the anode proper functioning. Check the correct assembly of anode wiring on related mainboard connector. If the error persists, replace mainboard | WAARSCHUWING |
| 332 WAARSCHUWING | Mainboard – WiFi board missing communication | Check cables between motherboard and HMI. If the error persists, replace the HMI module. If WiFi not present: Enter to the Installer Menu and set P31 OFF. If the error occurs again, replace the Main Board | WAARSCHUWING |
| 333 WAARSCHUWING | Mainboard – WiFi board missing communication | Check cables between motherboard and HMI. If the error persists, replace the HMI module. If WiFi not present: Enter to the Installer Menu and set P31 OFF. If the error occurs again, replace the Main Board | WAARSCHUWING |
| 334 WAARSCHUWING | Missing Communication between Inverter and main board | Check the communication cable and the related motherboard and TDC cables. If the error persists, replace the TDC | WAARSCHUWING |
| 336 WAARSCHUWING | Touch screen not working | Reset the product by pressing the ON / OFF button twice. If the error persists, replace the HMI | WAARSCHUWING |
| 337 WAARSCHUWING | Cascade master missing | Check that at least one of the products in the cascade is set as Master, otherwise set one | WAARSCHUWING |
| 314 INFORMATIE | ON / OFF repeated | Wait 15 minutes before unlocking the product with ON/OFF button | INFORMATIE |
Probleemoplossing - ATAG Energion Nuos Plus 200
Veelvoorkomende problemen en oplossingen - ook zonder foutcode op het display.
Overige problemen 12
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Water delivered is cold or insufficiently hot | Machine malfunctioning | Check for errors on the display and follow the instructions on the Errors table |
| Verminderde werking van de warmtepomp, elektrisch verwarmingselement werkt bijna continu | Problemen met het warmtepompcircuit | Controleer het display op foutmeldingen |
| Er komt een slechte geur uit het product | Lekken of gedeeltelijke verstoppping in het koudemiddelcircuit | Schakel het product IN in warmtepompmodus, gebruik een lekdetector voor het specifieke circuit |
Verbinding & Smart Home 2
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Water delivered is cold or insufficiently hot | HC/HP signal missing (if the product is installed with EDF signal cable) | To check the operation of the product start the Boost mode; if the outcome is positive check the presence of the HC/HP signal from the meter and check that the EDF cabling is intact |
| Problemen met het weergeven van het display of het display gaat uit | Storing of elektrische verbindingsproblemen tussen het moederbord en de interface PCB | Controleer de verbindingsstatus en de correcte werking van de PCB's |
Onderhoud & Verzorging 4
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Water delivered is cold or insufficiently hot | Insufficient air flow to the evaporator | Clean the grilles and ducts regularly |
| Water is boiling (with possible steam on the taps) | High level of limescale build-up in the boiler and components | Unplug the power supply, empty the appliance, remove the heating element sheath and clean the limescale from the inside of the boiler, taking care not to damage the enamel on the boiler and the heating element sheath. Reassemble the product in its original configuration. Replace the flange gasket |
| Verminderde werking van de warmtepomp, elektrisch verwarmingselement werkt bijna continu | Verdamper verstopt of bevroren | Zorg ervoor dat de verdamper schoon is |
| Er komt een slechte geur uit het product | Geen sifon of sifon is leeg | Installeer een sifon. Zorg ervoor dat deze de nodige hoeveelheid water bevat |
Geluiden & Trillingen 2
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Verhoogde geluidsniveau | Aanwezigheid van een interne verstopping | Controleer de bewegende onderdelen van de eenheid, reinig de ventilator en andere bewegende delen die lawaai kunnen veroorzaken |
| Verhoogde geluidsniveau | Sommige onderdelen trillen | Controleer de onderdelen die zijn verbonden met mobiele klemmen, zorg ervoor dat de schroeven goed zijn aangedraaid |
Prestaties & Werking 1
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Verminderde werking van de warmtepomp, elektrisch verwarmingselement werkt bijna continu | Er zijn nog geen 8 dagen verstreken sinds de eerste inbedrijfstelling, Time W-parameterwijziging of stroomstoring | Wacht 8 dagen |
Stroomvoorziening & Elektronica 4
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Water delivered is cold or insufficiently hot | No electrical connection, wires disconnected or damaged wires and connections | Check the voltage on the power terminals, check the condition of the wires and connections |
| Water delivered is cold or insufficiently hot | Product is switched OFF | Check the mains power supply. Switch the product ON |
| Verminderde werking van de warmtepomp, elektrisch verwarmingselement werkt bijna continu | Installatie uitgevoerd met niet-conforme elektrische stroomvoorziening (spanning te laag) | Voer het product uit met de juiste spanning |
| Problemen met het weergeven van het display of het display gaat uit | Stroomverzorging defect | Controleer de voeding |
Temperatuurproblemen 6
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Water delivered is cold or insufficiently hot | Temperature setting is low | Raise the water temperature setting |
| Water delivered is cold or insufficiently hot | Malfunctioning of the timer for the two-tier rate (if the product is installed with this configuration) | Check the operation of the day/night meter and that the set time is sufficient to heat the water |
| Water delivered is cold or insufficiently hot | Use of a significant amount of hot water when the product is in heating phase | Wait for the heating phase to complete |
| Water is boiling (with possible steam on the taps) | Sensor error | Check for NTC errors, even occasional ones |
| Verminderde werking van de warmtepomp, elektrisch verwarmingselement werkt bijna continu | Sensorfout | Controleer op NTC-fouten, ook incidentele |
| Verminderde werking van de warmtepomp, elektrisch verwarmingselement werkt bijna continu | Time W-waarde te laag | Stel een lagere temperatuurparameter of een hogere Time W-parameter in |
Waterproblemen 2
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Onvoldoende warm waterstroom | Lekkages of verstopping in het hydraulische circuit | Controleer het circuit op lekkages, controleer de toestand van de deflector op de koude watertoevoerpijp en de integriteit van de afvoerhete waterpijp |
| Water lekt uit het drukveiligheidsapparaat tijdens de verwarmingsfase | Het is normaal dat er enig water uit het apparaat op het leveringssysteem druppelt | Als het lek na de verwarmingsfase aanhoudt, controleer dan de afstelling van het apparaat en de netzekerheid. Om te voorkomen dat water druppelt, moet een expansievat worden geïnstalleerd. Blokkeer nooit de uitlaat van het apparaat |
Community-vragen
Stel een vraag
De foutcodes zijn afkomstig uit de officiële handleiding van de fabrikant.
Bezoek de officiële ATAG website voor actuele informatie en ondersteuning.