Ultimaker 2 Go
Printer · 5 Display-foutcodes · 5 Probleemoplossingen
Foutcodes - Ultimaker 2 Go
Deze codes worden op het display van uw apparaat weergegeven wanneer er een probleem wordt gedetecteerd.
| Foutcode | Beschrijving | Oplossing | Ernst |
|---|---|---|---|
| ERROR - HEATER ERROR KRITIEK | De verwarmingsfout treedt op wanneer de sensor geen stabiele temperatuurstijging registreert. Dit kan betekenen dat de verwarmingscartridge niet goed is aangesloten. | 1. Controleer of de verwarmingscartridge goed is aangesloten op het moederbord. 2. Zorg ervoor dat alle verbindingen stevig zijn. 3. Controleer of de verwarmingscartridge zelf niet beschadigd is. 4. Schakel de machine uit en weer in om opnieuw te proberen. | KRITIEK |
| ERROR - STOPPED TEMP SENSOR KRITIEK | Probleem met de PT100 B sensor die de temperatuur van de nozzle meet. De sensor registreert incorrecte waarden en voorkomt uit veiligheidsredenen dat de nozzle opwarmt. | 1. Controleer de verbinding van de PT100 B sensor aan het moederbord. 2. Vergewis je ervan dat alle verbindingen goed zijn aangesloten. 3. Controleer of de sensor zelf beschadigd is. 4. Vervang de sensor indien deze beschadigd blijkt te zijn. | KRITIEK |
| X OR Y SWITCH BROKEN KRITIEK | Deze fout treedt op wanneer de X of Y eindschakelaar niet wordt geactiveerd tijdens het positioneren van de printerkop. | 1. Controleer of de X of Y eindschakelaar fysiek beschadigd is. 2. Vergewis je ervan dat niets de schakelaar blokkeert. 3. Controleer de verbinding van de schakelaar met het moederbord. 4. Voer een herpositionering uit. 5. Vervang de schakelaar indien deze beschadigd is. | KRITIEK |
| Z-SWITCH BROKEN KRITIEK | Er is een probleem met de Z-eindschakelaar. De schakelaar kan niet worden ingedrukt of functioneert niet correct. | 1. Controleer of de Z-endschakelaar fysiek beschadigd is. 2. Vergewis je ervan dat niets de schakelaar blokkeert of tegenhoudt. 3. Controleer de verbinding van de schakelaar met het moederbord. 4. Vervang de schakelaar indien deze beschadigd is. | KRITIEK |
| Z-SWITCH STUCK KRITIEK | Er is een probleem met de Z-eindschakelaar. Het hefboom van de schakelaar kan niet terugspringen. | 1. Controleer of iets de hefboom van de Z-schakelaar blokkeert. 2. Verwijder voorzichtig eventuele obstructies. 3. Vergewis je ervan dat de schakelaar vrij kan bewegen. 4. Controleer de verbinding met het moederbord. 5. Vervang de schakelaar indien deze beschadigd is. | KRITIEK |
Probleemoplossing - Ultimaker 2 Go
Veelvoorkomende problemen en oplossingen - ook zonder foutcode op het display.
Verbinding & Smart Home 1
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Cannot connect to Cura | Cura does not recognize the Ultimaker 2 Go during firmware upload due to a software or hardware connection error | 1. Ensure everything is correctly connected (power and USB cable) and that the Ultimaker 2 Go is turned on. Try a different USB cable if possible. 2. Check that the latest version of Cura is installed on your computer. 3. Try connecting to another computer, preferably with a different operating system. |
Prestaties & Werking 2
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Extrusion problems - complete blockage | The nozzle is completely clogged by dirt or carbonized material in the nozzle or other part of the hotend | 1. Check if the filament is not stripped in the feeder and remove it if necessary. 2. Ensure the tension on the feeder is as loose as possible (white insert clip at the top). 3. Try to manually extrude material via the 'Move material' option in the Advanced menu, and push the material manually at the feeder for extra force. 4. Use the Atomic Method to remove dirt or carbonized material from the hotend. |
| Extrusion problems - under-extrusion | The Ultimaker 2 Go does not extrude enough plastic, resulting in thin or missing layers. This can be caused by dirt or carbonized material in the hotend, or by a deformed PTFE coupler | 1. Check if the filament is not stripped in the feeder and remove it if necessary. 2. Ensure the tension on the feeder is as loose as possible (white insert clip at the top). 3. Try to manually extrude material via the 'Move material' option in the Advanced menu, and push the material manually at the feeder for extra force. 4. Use the Atomic Method to remove dirt or carbonized material from the hotend. 5. Check the PTFE coupler for deformation (a small ridge on the inside at the bottom indicates wear) and replace if necessary. |
Spoelresultaat & Droging 2
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Print does not stick to the build plate - poor first layer adhesion | The first layer does not stick well enough due to insufficient build plate alignment or damaged blue tape | 1. Ensure the build plate is correctly aligned for a good first layer. 2. Replace the blue tape regularly because it must not be too damaged for good adhesion. |
| Print does not stick to the build plate - warping | The plastic curls because plastics tend to shrink quickly when they cool, which occurs especially at the corners | 1. Ensure the build plate is correctly aligned for a good first layer. 2. Replace the blue tape regularly because it must not be too damaged for good adhesion. 3. Use the 'Brim' function in Cura, which places a single-layer flat area around your object for a larger adhesion surface to prevent warping. |
Community-vragen
Stel een vraag
De foutcodes zijn afkomstig uit de officiële handleiding van de fabrikant.
Bezoek de officiële Ultimaker website voor actuele informatie en ondersteuning.