Canon i-SENSYS MF6550
Printer · 8 Display-foutcodes · 18 Probleemoplossingen
Foutcodes - Canon i-SENSYS MF6550
Deze codes worden op het display van uw apparaat weergegeven wanneer er een probleem wordt gedetecteerd.
Meest voorkomende foutcodes - Canon i-SENSYS MF6550
#0001
Document may be jammed
WAARSCHUWING
#0003
Document of 630 mm or longer from ADF, or document contains ...
WAARSCHUWING
#0005
The other fax machine did not respond within 35 seconds, or ...
WAARSCHUWING
#0009
Paper has run out or paper cassette is not set properly
WAARSCHUWING
#0018
There is no reply when you redial, or fax signal was not ret...
WAARSCHUWING
| Foutcode | Beschrijving | Oplossing | Ernst |
|---|---|---|---|
| #0001 WAARSCHUWING | Document may be jammed | Remove the jammed document | WAARSCHUWING |
| #0003 WAARSCHUWING | Document of 630 mm or longer from ADF, or document contains too much data, or document takes a long time to receive | Divide the document into smaller parts and send from the platen glass, or reduce the scanning resolution before sending, or contact the other party to reduce their scanning resolution | WAARSCHUWING |
| #0005 WAARSCHUWING | The other fax machine did not respond within 35 seconds, or the other party may not be using a G3 fax machine | Send the document again and contact the other party to check their fax machine, or verify the other party has a G3 fax machine and try a compatible transmission mode | WAARSCHUWING |
| #0009 WAARSCHUWING | Paper has run out or paper cassette is not set properly | Load the paper or reset the paper cassette properly | WAARSCHUWING |
| #0018 WAARSCHUWING | There is no reply when you redial, or fax signal was not returned as the other party's line was engaged | Check that the other party's line is not engaged and try again from the beginning | WAARSCHUWING |
| #0037 WAARSCHUWING | The memory is full | Print, send, or delete any documents stored in memory | WAARSCHUWING |
| #0012 INFORMATIE | Could not send because the other party's fax machine is out of paper | Contact the other party and ask them to load the paper | INFORMATIE |
| #0995 INFORMATIE | Communication reservation is pending | Wait for the reservation to complete or cancel if necessary | INFORMATIE |
Probleemoplossing - Canon i-SENSYS MF6550
Veelvoorkomende problemen en oplossingen - ook zonder foutcode op het display.
Overige problemen 9
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| SYSTEM ERROR bericht op het LCD-scherm | Er is een systeemfout opgetreden in de machine | Zet de hoofdschakelaar uit, wacht meer dan 10 seconden, en zet het apparaat weer aan. Als het bericht aanhoudt, ontkoppel de machine van het stopcontact en neem contact op met een geautoriseerde Canon-dealer of de Canon-helpline |
Onderhoud & Verzorging 3
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| TONER IS NOT SET bericht op het LCD-scherm | Tonercartridge is niet geïnstalleerd of niet correct geïnstalleerd | Installeer de tonercartridge correct in de machine |
| TONER LOW bericht op het LCD-scherm | Toneraanbod raakt op | Verwijder de tonercartridge en schud deze 5 tot 6 keer goed door om de toner gelijkmatig te verdelen. Plaats de cartridge opnieuw. Als het bericht aanhoudt, vervang de tonercartridge |
| PLATEN GLASS DIRTY bericht op het LCD-scherm | ADF-scangebied aan de linkerkant van het platen glas is vuil | Reinig het ADF-scangebied en druk op OK |
Paper 6
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Papieropstopping in de machine | Document of papier zit vast in de machine | Open het deksel, localiseer de jam-locatie op het LCD-scherm, en verwijder voorzichtig het vastgezette papier. Hou het verwijderde papier niet met kracht eruit. |
| CHECK DOCUMENT bericht op het LCD-scherm | Document zit vast in de ADF of papierinvoer | Verwijder het vastgezette document uit de ADF of de papieruitvoergleuf voorzichtig |
| DOCUMENT TOO LONG bericht op het LCD-scherm | Document is langer dan 630 mm of wordt niet correct gevoerd | Scan het document op het platen glas, of verklein het document tot minder dan 630 mm |
| CHANGE PAPERSIZE bericht op het LCD-scherm | Papierformaat in cassette komt niet overeen met ingesteld formaat | Laad papier van het juiste formaat in de cassette of multipurpose tray, en verander de papierformaatinstelling in het COMMON SETTINGS menu |
| LOAD PAPER bericht op het LCD-scherm | Er is geen papier geladen in de cassette of multipurpose tray, of deze is niet correct ingebracht | Plaats de papiergroep zo ver mogelijk in de cassette of laad papier in de multipurpose tray |
| OUTPUT TRAY FULL bericht op het LCD-scherm | Papieruitvoerlade is vol met afdrukken | Verwijder de afdrukken uit de papieruitvoerlade |
Community-vragen
Stel een vraag
De foutcodes zijn afkomstig uit de officiële handleiding van de fabrikant.