Delonghi Magnifica Evo ECAM292.81.B
Koffiezetapparaat · 1 Display-foutcodes · 20 Probleemoplossingen
Foutcodes - Delonghi Magnifica Evo ECAM292.81.B
Deze codes worden op het display van uw apparaat weergegeven wanneer er een probleem wordt gedetecteerd.
| Foutcode | Beschrijving | Oplossing | Ernst |
|---|---|---|---|
| E6 WAARSCHUWING | De melkverbinding (E6) is niet correct geplaatst | Controleer of de melkkan volledig is en of alle onderdelen correct zijn geplaatst. Zorg ervoor dat de melkverbinding goed is aangesloten. Raadpleeg hoofdstuk '14. VOLLEDIG SCHOONMAKEN VAN DE MELKKAN' voor correcte plaatsing. | WAARSCHUWING |
Probleemoplossing - Delonghi Magnifica Evo ECAM292.81.B
Veelvoorkomende problemen en oplossingen - ook zonder foutcode op het display.
Overige problemen 8
| Probleem | Oorzaak | Oplossing |
|---|---|---|
Installatie & Opstelling 1
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Coffee flows very slowly or in drops | Injector was not placed after cleaning | Place the injector according to the description in chapter '15. INJECTOR CLEANING'. |
Onderhoud & Verzorging 2
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Coffee is not hot | Machine requires descaling | Perform descaling. Then check water hardness ('5. Water hardness measurement') and confirm the device is set according to actual hardness ('12. SETTINGS MENU'). |
| Coffee flows very slowly or in drops | Internal machine is very dirty | Clean the machine thoroughly. If the message continues after cleaning, contact customer service or an authorized support center. |
Prestaties & Werking 1
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Coffee flows very slowly or in drops | Ground coffee is too fine | Adjust the grinder setting ('8.8 Grinder adjustment'). The result is visible only after making at least 2 coffees first. |
Stroomvoorziening & Elektronica 1
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Machine does not turn on | Power cable is not connected to the outlet | Connect the power cable to the outlet. |
Spoelresultaat & Droging 3
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Coffee is not full or has little crema | Ground coffee is too coarse | Adjust the grinder setting ('8.8 Grinder adjustment'). The result is visible only after making at least 2 coffees first. |
| Coffee is not full or has little crema | Wrong coffee blend used | Use a coffee blend suitable for espresso machines. |
| Coffee is not full or has little crema | Coffee is not fresh | Check the coffee packaging. If it has been open for a long time, the coffee has lost its flavor. Replace with fresh coffee. |
Temperatuurproblemen 3
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Machine turns on but coffee is not hot | Cups were not preheated | Heat the cups with hot water before making coffee. You can use the hot water function. |
| Machine turns on but coffee is not hot | Internal circuits have cooled down after 2-3 minutes since last coffee | Before making coffee, heat the internal circuits by running a rinse cycle. Hold button (B6) pressed for a few seconds. |
| Coffee temperature is low | Temperature setting is too low | Set a higher coffee temperature from the settings menu (see chapter '12. SETTINGS MENU'). |
Waterproblemen 1
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Water circuit is empty | Hydraulic circuit needs priming | Run hot water by pressing the corresponding button (Hot Water) until water flows normally. |
Community-vragen
Stel een vraag
De foutcodes zijn afkomstig uit de officiële handleiding van de fabrikant.