BEKO DFS05013W
Afwasmachine · 20 Probleemoplossingen
Probleemoplossing - BEKO DFS05013W
Veelvoorkomende problemen en oplossingen - ook zonder foutcode op het display.
Overige problemen 9
| Probleem | Oorzaak | Oplossing |
|---|---|---|
Onderhoud & Verzorging 4
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| There is a different odour in the machine | Filters are clogged or dirty dishes are kept in dishwasher for 2-3 days | Check if the filter system is clean. Clean the filter system regularly. If you are not going to start the machine right after you have put the dishes into it, remove the remnants on the dishes and run the Prewash programme without detergent every 2 days. Do not close the door of the machine completely in order to avoid odour build up in machine. You can also use commercially available odour removers or machine cleaners. |
| Rust, discoloration or surface deterioration occurs on dishes | Salt leakage exists, salty food remnants have remained on dishes for a long time, electric installation is not grounded, intensive cleansers such as bleaches are used, metal items are used for purposes other than their intended uses, cutlery are made of low quality stainless steel, or kitchen utensils that are already corroded are washed in dishwasher | Pay attention not to spill salt around the salt filling hole while adding salt. Make sure that the salt reservoir lid is tightly closed after finishing the filling process. Run the prewash programme to remove the salt that spilled inside the machine. If cutlery soiled with salty foods will be kept waiting in machine, dirt must be removed by prewash or dishes must be washed without being kept waiting. Check if your machine is connected to the actual grounding line. Do not wash your dishes with bleach. Do not use metal kitchen utensils out of their intended uses. Do not wash low quality stainless steel or corroded items in dishwashers. |
| Dishes are scratched | Salt leakage exists, water hardness setting is low or salt level is insufficient, or dishes are not placed orderly in the machine | Pay attention not to spill salt around the salt filling hole while adding salt. Make sure that the salt reservoir lid is tightly closed after finishing the filling process. Run the prewash programme to remove the salt that spilled inside the machine. Measure the hardness of the supply water appropriately and check the water hardness setting. When placing the glasses and other glassware into the basket lean them not against other dishes but the edges or racks of the basket or the glass support tines. |
| Schuim vormt zich in de machine | Borden worden met handafwasmiddel met de hand gewassen maar niet gespoeld voordat ze in de machine worden geplaatst, spoelmiddel is in de machine gemorst bij het toevoegen van spoelmiddel, of het deksel van het spoelmiddelreservoir staat open | Het is niet nodig om de borden voor het plaatsen in de machine met de hand af te wassen. Het verwijderen van grove vuil op de borden onder stromend water met een tissue of vork is voldoende. Zorg ervoor dat spoelmiddel niet in de machine wordt gemorst wanneer u het vult. Maak gemorst spoelmiddel schoon met behulp van tissue/handdoek. |
Prestaties & Werking 4
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Dishes are not washed clean | Dishes not placed orderly, unsuitable programme, impellers stuck or clogged, filters clogged or installed incorrectly, baskets overloaded, detergent stored under unsuitable conditions, detergent insufficient, rinse aid insufficient, or detergent dispenser lid left open | Load the dishes as described in the user manual. Select a programme with a higher temperature and cycle time. Turn the lower and upper impellers by hand to make sure that they rotate freely. Clean the impellers and filters regularly. Do not overload the baskets. Store detergent in a closed container or use tablet detergents. Adjust the amount of detergent according to the soiling degree. Check the rinse aid indicator and add rinse aid if necessary. Make sure that the detergent dispenser lid is closed tightly after adding detergent. |
| Dishes are not dry at the end of cycle | Dishes not placed orderly, rinse aid insufficient, machine unloaded right after programme is over, unsuitable programme selected, or surface quality of kitchen utensils is deteriorated | Place your dishes in a way that no water will accumulate in them. Check the rinse aid indicator and add rinse aid if necessary. Do not unload your machine right after washing process is completed; slightly open the door and wait for evacuation of the steam inside. Unload the dishes after the pieces cool down to a touchable level. Start unloading process from the lower basket. Select programmes with longer duration for a higher drying performance. Do not wash kitchen utensils with deteriorated surfaces in dishwasher. |
| Tea, cafe or lipstick stains remain on dishes | Selected programme is unsuitable, surface quality of kitchen utensils is deteriorated, or detergent stored under unsuitable conditions | Select a programme with a higher temperature and cycle time. Do not wash kitchen utensils with deteriorated surfaces in dishwasher. Store detergent in a closed container or use tablet detergents. |
| Detergent remains in detergent dispenser | Detergent dispenser was damp when adding detergent, detergent is added long before the washing process, opening of the detergent dispenser lid is prevented during washing, detergent is stored under unsuitable conditions, or impeller holes are clogged | Make sure that the detergent dispenser is dried well prior to filling it with detergent. Pay attention to add detergent shortly before start-up of the washing. Place the dishes in a way that will not prevent the detergent dispenser lid from opening and the water going into the machine from impellers. Store detergent in a closed container or use tablet detergents. Clean the impellers regularly. |
Stroomvoorziening & Elektronica 1
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Machine does not start | Power cable is unplugged, fuse is blown, water is cut, door is open, or On/Off button is not pressed | Check if the power cable is plugged in. Check the fuses in your house. Make sure that the water inlet tap is open. Make sure that you have closed the door of the machine. Make sure that you have turned on the machine by pressing the On/Off button. |
Waterproblemen 2
| Probleem | Oorzaak | Oplossing |
|---|---|---|
| Lime traces remain on dishes and glassware gains a misty appearance | Rinse aid is not sufficient, water hardness setting is low or salt level is insufficient, or salt leakage exists | Check the rinse aid indicator and add rinse aid if necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the machine. Measure the hardness of the supply water appropriately and check the water hardness setting. Pay attention not to spill salt around the salt filling hole while adding salt. Make sure that the salt reservoir lid is tightly closed after finishing the filling process. Run the prewash programme to remove the salt that spilled inside the machine. |
| A smear remains on glasses that resembles milk stain which can not be removed when wiped by hand. A bluish / rainbow appearance occurs when the glass is pointed to light | Excessive rinse aid is used or corrosion has occurred on glass due to soft water | Lower rinse aid setting. Clean the spilled rinse aid when adding rinse aid. Measure the hardness of the supply water appropriately and check the water hardness setting. If your supply water is soft (<5 dH), do not use salt. Choose programmes that wash in higher temperatures (e.g. 60-65°C). You can also use glass protective detergents that are commercially available. |
Community-vragen
Stel een vraag
De foutcodes zijn afkomstig uit de officiële handleiding van de fabrikant.